If you’ve ever stood next to a running plastic injection mould machine, you’ve probably heard those little clinks when the mould platen slides back to eject a finished part. Those claps? That’s ejector pins—super tiny, but they’re the unsung heroes of getting parts out without scratching or warping the whole thing. As a mould components supplier, I get asked this question at least once a week: “What’s the standard size of an ejector pin?” It’s not a one-size-fits-all answer, but I’ll break it down like I would with a customer who’s staring at a CAD file and panicking because their last set of pins was way too wobbly. Mould Components

First off, let’s set a quick base: ejector pins are basically hardened steel rods that push on the part’s inner surface, right? They run through the mould’s core half, and the size has to be tight enough not to bend when they’re pushing 10,000+ PSI of plastic, but not so big that they leave a huge mark on the part. That balance is everything. Now, when people say “standard size,” they’re not talking about random lengths from a hardware store. We’re dealing with industry norms that most mould makers and mould component suppliers stick to, because if you don’t follow those, you’ll end up with pins that don’t fit the mould plate’s holes or break on the first run.
Let’s start with the diameter, since that’s the number people usually care about first. The most common standard range I see across North America, Europe, and even a lot of Asian mould shops is 1mm up to 20mm. Wait, let’s narrow that down: 1mm to 12mm is the sweet spot for small to medium parts—think phone casings, toy pieces, small appliance knobs. Why? Any smaller than 1mm and you’re asking for bending, especially if the part has deep pockets that need a long pin to reach. Bending a 0.8mm pin mid-eject means the part gets a big, ugly scratch, and you’re replacing pins every 500 cycles, which kills production time. On the flip side, pins over 20mm? Those are usually custom, because a pin that wide would leave a massive witness mark on a part, and you’d only use those if you’re pushing on a really large, flat area of a big component—like a automotive bumper insert.
But wait, there’s a sub-category here for “micro ejector pins.” If you’re working on medical parts, tiny electronic connectors, or something with features smaller than a grain of rice, the standard drops to 0.5mm to 0.9mm. These aren’t the cheap off-the-shelf ones, though—they’re made with super precise grinding to stay straight, because even a 0.01mm wobble will break a micro pin on the first shot. I’ve had a customer come to me last month because they tried to use a 0.7mm regular pin for a insulin pen part, and every 100 cycles, two pins snapped. We swapped them for micro-grade hardened pins, and now they’re at 10,000 cycles no issues. That’s the difference between knowing the standard and just guessing.
Now, the length is trickier than diameter. A lot of new mould makers forget that standard length isn’t just how long the pin is, it’s the “ejector stroke length” plus the depth the pin has to reach into the part, plus the thickness of the mould plate and the ejector plate. The industry norm for standard pin lengths is 50mm to 500mm—but that’s only for common mould plate thicknesses. Wait, no, let’s be real: we split lengths into two standard groups: “stock standard pins” and “custom length pins.” Stock standard pins are cut to lengths that work for 90% of basic moulds: 50mm, 75mm, 100mm, 125mm, 150mm, 200mm, 250mm, 300mm. If your mould’s throw is longer than 200mm, you can’t get that off the shelf—you have to order a custom cut pin, because the stock ones don’t go longer than 300mm before the steel starts to lose its hardness along the whole rod.
But here’s a rule I live by as a supplier: the “effective length” of the pin (that’s the part sticking through the mould core, not the part inside the ejector plate) should never be more than 10 times the diameter. Let’s test that: if you have a 2mm pin, its max effective length is 20mm. If you need it to reach 25mm to push on the part, you either go up to a 2.5mm pin or add a support pin behind it (those are the small backup pins we also sell) so the main pin doesn’t bend. I can’t tell you how many times a new mould maker has come to me with a 2mm pin stretched to 28mm, wondering why it’s bowing and leaving a crooked mark on the part. That 10x rule is the unofficial standard that every experienced mould shop follows, even if the number “20mm” isn’t written in some ISO book.
Wait, let’s talk about tolerances too, because size isn’t just the number—it’s how precise that number is. The standard tolerance for ejector pins is h7 for the outer diameter. What does that mean? It means the pin is 0 to -0.015mm smaller than the listed diameter, so it slides perfectly into the mould plate’s hole without wiggling, but not so tight that it seizes after a few cycles. If you get a pin with a tolerance of h11, that’s a lot looser, and you’d only use it for non-critical applications, like a mould that’s only going to make 100 parts. But for production moulds, h7 is the gold standard. I once had a customer complain that their pins were sticking halfway through eject, and when we measured them, they had a tolerance of h10—they were too loose and the pin was twisting in the hole, binding. Swapping to h7 pins fixed that in a day.
Also, don’t forget about the head of the ejector pin, because that’s part of the size and it’s just as important. The standard head size for most pins is 5mm larger than the diameter of the pin shaft. So a 2mm pin has a 7mm head, a 5mm pin has a 10mm head, and so on. The head sits in the ejector plate, pushing on the plate when the mould opens, so it needs to be big enough to distribute the force without sinking into the plate. The tolerance for the head is usually m6, so it’s a press fit into the ejector plate hole—no sliding, no wiggling, which is key for consistent ejection. I’ve had a couple of customers try to cut corners by using a head smaller than standard, and after a few thousand cycles, the head wore down and the pin stopped pushing the whole part out. That’s a costly mistake.
Now, let’s bust some myths here, because I get these all the time. First myth: “Standard size is the same for all materials.” Nope. If you’re moulding a soft plastic like PE for a grocery bag, you can use a smaller pin because the part doesn’t need a lot of force to eject. If you’re moulding a hard plastic like ABS or PC for a car dashboard, you need a thicker pin (maybe 1mm larger than standard) because the plastic is stiffer and needs more force to push, so a thin pin would bend. Another myth: “All ejector pins are round.” No, there are rectangular pins, flat pins, even custom shaped pins for parts with thin walls, but those are special order—round is the standard for 95% of applications, which is why all our stock pins are round.
Wait, let’s throw in a real example to make this concrete. Last quarter, I worked with a customer who was making a set of small appliance control knobs. The CAD called for 4 pins, each needing to reach 18mm into the part. The part was made of hard ABS, so we followed the 10x rule: they needed a 1.8mm pin (since 1.8 x 10 = 18mm effective length). We used standard h7 tolerance, 23mm total length (18mm effective plus 5mm for the head and ejector plate), and 6.8mm heads (5mm larger than 1.8mm). They ordered 500 pins, and they told me last week that they haven’t had a single ejection defect in 20,000 cycles. That’s exactly what the standard is for—making sure parts work consistently without headaches.
Now, what if your part is weird? Like, it has a super thin wall, or a deep undercut, or a tiny feature that only has 1mm of space to push. Then you don’t stick to the standard—you adjust, but you still use the standards as a starting point. For example, if you need a 0.5mm pin to reach 6mm, that’s 12x the diameter, which is over the 10x rule, so you’d add a support pin right next to it. Or if you need an off-diameter, like a 3.2mm pin instead of the standard 3mm, that’s fine—we can grind that to exact size, you just can’t get it off the shelf. The standard is a baseline, not a rigid rule that you have to follow even when it makes no sense for your part.
So to wrap this up, the standard size of an ejector pin isn’t a single number—it’s a range that depends on your part size, material, ejection force, and mould plate. The baseline numbers are: diameter 1mm to 20mm (micro pins 0.5mm to 0.9mm), standard lengths 50mm to 300mm, h7 tolerance for the shaft, m6 for the head, and a head 5mm larger than the shaft. The unofficial golden rule is effective length max 10x the shaft diameter, to avoid bending. Every mould shop uses these norms, which is why you can walk into any mould component supplier and ask for a standard 2mm x 100mm ejector pin, and they’ll know exactly what you mean.

If you’re working on a new project, or your current pins are giving you trouble (bending, sticking, leaving marks), hit me up to talk through what you need. No jargon, no sales pitch—just straight answers about what size and type of pin will work for your parts.
Plastic Mould References
- Injection Molding Design Guide, Society of Plastics Engineers (SPE), 2022
- Mould Component Standards, International Organization for Standardization (ISO) 10360-7, 2021
- Ejection System Design for Plastic Moulds, Tooling & Manufacturing Association (TMA), 2020
- Precision Ejector Pin Specifications, Industrial Tooling Association (ITA), 2023
Wuxi Santaizi Metal Products Co., Ltd.
As one of the most professional mould components manufacturers and suppliers in China, we warmly welcome you to buy high-grade mould components made in China here from our factory. All customized metal products are with high quality and competitive price. Contact us for pricelist.
Address: No. 23 Xufeng Road, Xushe Town, Yixing City, Wuxi City, Jiangsu Province, China
E-mail: Ksstzmj@163.com
WebSite: https://www.wuxisantaizi.com/