{"id":3604,"date":"2026-11-09T10:52:10","date_gmt":"2026-11-09T02:52:10","guid":{"rendered":"http:\/\/www.primamahamaju.com\/blog\/?p=3604"},"modified":"2026-11-09T10:52:10","modified_gmt":"2026-11-09T02:52:10","slug":"what-are-the-torque-requirements-for-tightening-jis-flanges-4bf9-ac1285","status":"publish","type":"post","link":"http:\/\/www.primamahamaju.com\/blog\/2026\/11\/09\/what-are-the-torque-requirements-for-tightening-jis-flanges-4bf9-ac1285\/","title":{"rendered":"What are the torque requirements for tightening JIS flanges?"},"content":{"rendered":"<p>If you\u2019ve ever worked with JIS flanges (that\u2019s Japanese Industrial Standard, for the uninitiated) and wondered how tight is tight enough\u2014chances are you\u2019ve guessed wrong at some point, or have seen a leaky pipe, a wobbly tank, or even a bolt that snapped mid-torque wrench crank. As a supplier who\u2019s dealt with JIS and KS flanges day in and day out for over 8 years, I can tell you torque is not a \u201cguess it and check\u201d game. It\u2019s the difference between a system that runs flawlessly for years and a headache that hits out of nowhere. Let\u2019s break this down, no overly technical jargon, just real stuff that applies to what we sell. <a href=\"https:\/\/www.cncjflange.com\/stainless-steel-flange\/jis-flanges\/\">JIS &#038; KS Flanges<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.cncjflange.com\/uploads\/43420\/small\/butt-weld-reducer0fa3c.jpg\"><\/p>\n<p>First, let\u2019s get one thing straight: JIS flanges aren\u2019t the same as ANSI (American) or DIN (German) flanges. That\u2019s the number one mistake I see contractors make\u2014they grab their go-to ANSI torque chart and slam it on a JIS 10K flange, and boom, either the bolt stretches too far or the gasket crushes unevenly. KS flanges are basically the Korean counterpart, almost identical to JIS, but with a few tiny tweaks that change torque just enough to matter. I\u2019ve had a guy show up with a stack of KS flanges and an ANSI chart, and halfway through tightening, one of the bolts snapped. He was mad at the flange (weird, right?) until I pointed out the difference.<\/p>\n<p>So what actually determines torque requirements? It\u2019s not just \u201cthe flange size.\u201d Let\u2019s list the real factors, not the textbook ones:<\/p>\n<ol>\n<li>\n<p>Flange rating and size. JIS flanges are rated by pressure class\u2014most common are 5K, 10K, 16K, 20K. KS uses the same system, for the most part. A 5K 2-inch flange is for low-pressure stuff, like water lines in a building, while a 20K 8-inch flange is for high-pressure steam or chemical lines. Bigger flanges need more torque, obviously, but not just linear\u2014doubling the diameter doesn\u2019t double the torque. Also, the number of bolts changes too: a 4-inch 10K JIS flange has 8 bolts, an 8-inch 10K has 16, so you have to split the total torque across all bolts evenly.<\/p>\n<\/li>\n<li>\n<p>Bolt material and grade. JIS bolts have their own grades too\u2014like JIS B 1180 for common carbon steel, JIS B 1181 for higher-tensile steel, even stainless steel (JIS B 1184). A Grade 8 ANSI bolt is way stronger than a basic JIS 4.6 carbon steel bolt, so you can\u2019t use the same torque. Last month, a client tried using cheap JIS 4.6 bolts for a 16K flange, and when we ran pressure tests, the bolts stretched way past their yield point\u2014no leaks, but we had to replace the whole set because they were permanently damaged. The high-tensile JIS 8.8 bolts we supply? They handle 30-40% more torque, no problem.<\/p>\n<\/li>\n<li>\n<p>Gasket type. This is the hidden variable I almost forgot. A soft rubber gasket for water lines doesn\u2019t need nearly as much torque as a metal ring gasket for chemical piping. If you over-tighten a soft gasket, it compresses too much and blows out, or the flange face gets damaged. If you under-tighten a metal gasket, you get tiny gaps that cause leaks. I once had a job where someone used a copper gasket on a JIS 10K flange and used ANSI torque\u2014by the time they were done, the gasket was so squashed it had zero sealing ability. We had to redo the whole thing with the right gasket and adjusted torque, cost the client extra, which we would\u2019ve avoided if we\u2019d talked first.<\/p>\n<\/li>\n<li>\n<p>Surface finish and flange face type. JIS flanges have two common face types: flat face (FF) and raised face (RF). Flat face is for low-pressure, non-corrosive stuff, and needs a bit less torque. Raised face is for higher pressure, has that little ring in the middle that the gasket sits on, so torque has to be precise\u2014too little and the gasket doesn\u2019t seal the raised area, too much and the raised face can deform. Also, if the flange face is rusty, scratched, or has old gasket gunk on it, that changes things\u2014you need more torque to compensate for uneven contact, or you\u2019ll get leaks even if the numbers are right.<\/p>\n<\/li>\n<\/ol>\n<p>Now, let\u2019s get to the actual numbers, because that\u2019s what everyone\u2019s here for. But before I post these, a disclaimer: these are baseline numbers, always adjust for the factors above. Also, we never go by just torque\u2014we do bolt stretch measurements too, because torque can be off by things like bolt lubrication, tool calibration, even how fast you crank the wrench.<\/p>\n<p>For JIS 10K flanges (super common, used in 90% of the jobs we supply):<\/p>\n<ul>\n<li>2-inch (50mm) flange: 8 bolts, each bolt gets ~45 lb-ft (61 Nm)<\/li>\n<li>4-inch (100mm) flange: 8 bolts, ~75 lb-ft (102 Nm) each<\/li>\n<li>6-inch (150mm) flange: 12 bolts, ~95 lb-ft (129 Nm) each<\/li>\n<li>8-inch (200mm) flange: 16 bolts, ~110 lb-ft (149 Nm) each<br \/>\nThese are for high-tensile JIS 8.8 bolts and standard rubber gaskets. If you\u2019re using metal gaskets, add 10-15 lb-ft per bolt. If you\u2019re on 5K JIS, subtract 15-20 lb-ft. For KS flanges, the numbers are almost identical\u2014we tested them last quarter, the only difference was 2-3 lb-ft for the 6-inch size, which is negligible for most jobs.<\/li>\n<\/ul>\n<p>For higher pressure, JIS 16K flanges:<\/p>\n<ul>\n<li>4-inch: ~100 lb-ft each<\/li>\n<li>6-inch: ~130 lb-ft each<\/li>\n<li>8-inch: ~160 lb-ft each<br \/>\nAgain, adjust for bolt grade and gasket type. I won\u2019t post 20K numbers because those are for industrial stuff, and you really should have a engineer spec them, but as a baseline, they\u2019re 50-60% higher than 10K.<\/li>\n<\/ul>\n<p>Wait, here\u2019s a pro tip I learned the hard way: never tighten all bolts in a circle at once. Do it in a crisscross pattern, half the torque, then full torque, then even a light re-tighten once the whole flange is assembled. For a 16-bolt 8-inch flange, that means bolt 1, then bolt 9, then bolt 5, then bolt 13, etc.\u2014skip every other bolt. That way, the gasket compresses evenly, no uneven pressure that causes leaks. I\u2019ve seen guys tighten bolt by bolt, clockwise, and by the time they get to the last one, the first is already over-tightened and the middle of the flange isn\u2019t even touching the gasket.<\/p>\n<p>Also, common mistakes to avoid:<\/p>\n<ul>\n<li>Using dry bolts. A lot of people forget to lubricate bolt threads. Dry bolts can have torque numbers off by 25-30% because of friction. We supply a light anti-seize compound with every flange order, free, because this is such a dumb mistake. Last month, a plumber showed up with dry bolts and his torque wrench reading was way lower than it should have been\u2014once he applied anti-seize, the reading jumped 18 lb-ft, and when we tested pressure, it held perfectly.<\/li>\n<li>Skipping the re-torque step. Flanges are metal, gaskets settle over the first 24 hours after installation. Even if you torque them to spec, you should re-torque them once the system is pressurized and cooled down. I can\u2019t tell you how many leaks we get calls about that are fixed with a simple re-torque.<\/li>\n<li>Ignoring flange condition. If the flange face is bent, or has a dent from shipping, torque won\u2019t fix it. We do a full inspection on every flange before it leaves our warehouse, but sometimes damage happens in transit, so always check the flange faces before you start installing.<\/li>\n<\/ul>\n<p>As a supplier who works with both JIS and KS flanges, one of the most common questions I get is: \u201cCan I use JIS bolts on KS flanges?\u201d The short answer is yes, 9 out of 10 times, as long as they\u2019re the same grade and size. The KS standard is basically a copy of JIS, with minor adjustments to bolt hole spacing that don\u2019t affect torque. The only time you need different torque is if the KS flange is rated higher than JIS, which is rare\u2014most KS flanges for commercial use are identical to JIS 10K.<\/p>\n<p>Another thing I see: people mixing bolt types. Don\u2019t use a stainless steel bolt on a carbon steel flange and expect the same torque as a carbon steel bolt. Stainless has a lower friction coefficient, so you need less torque to get the same bolt stretch. We label every bolt package with the correct torque for the flange it\u2019s paired with, so you don\u2019t have to guess.<\/p>\n<p>At the end of the day, torque requirements for JIS and KS flanges aren\u2019t arbitrary numbers made up by some standard organization. They\u2019re based on making sure the gasket compresses just enough to seal, the bolts don\u2019t break or stretch permanently, and the flange face doesn\u2019t get damaged. If you get this wrong, you\u2019re looking at leaks, downtime, extra costs, and even safety issues if it\u2019s high-pressure stuff.<\/p>\n<p>If you\u2019re working on a job, or planning a project, and you\u2019re not sure what torque to use\u2014don\u2019t guess. Hit us up to talk through your specific setup: flange size, rating, bolt grade, gasket type, pressure requirements. We\u2019ve been doing this long enough to know the ins and outs of both JIS and KS flanges, and we won\u2019t just throw a generic chart at you. We\u2019ll give you real numbers, pro tips, and even free anti-seize for your first order if you need it.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.cncjflange.com\/uploads\/43420\/small\/blind-flange-end3818d.jpg\"><\/p>\n<p>It\u2019s way better to get this right the first time than to deal with a leaky pipe or broken bolt halfway through a job. Save yourself the headache, reach out and let\u2019s work out the right torque for your flanges.<\/p>\n<p><a href=\"https:\/\/www.cncjflange.com\/stainless-steel-flange\/ansi-b16-5-flanges\/\">ANSI\/ASME B16.5 Flanges<\/a> References:<br \/>\nJapanese Industrial Standard (JIS) B 2220: Steel Flanges for Piping<br \/>\nKorean Industrial Standard (KS) B 1503: Steel Flanges for Pressure Piping<br \/>\nAmerican Society of Mechanical Engineers (ASME) PCC-1: Guidelines for Pressure Boundary Bolted Flange Joint Assembly<\/p>\n<hr>\n<p><a href=\"https:\/\/www.cncjflange.com\/\">Zhejiang Chengjiu Pipeline Co., Ltd.<\/a><br \/>Zhejiang Chengjiu Pipeline Co., Ltd. is one of the most professional jis flanges manufacturers and suppliers in China, specialized in providing high quality customized service. We warmly welcome you to buy high-grade jis flanges from our factory. For price consultation, contact us.<br \/>Address: NO.9-1 Hengsheng Road, Jinchuan Street, Changshan Prefecture, Quzhou, Zhejiang Province, China<br \/>E-mail: sale@cncjflange.com<br \/>WebSite: <a href=\"https:\/\/www.cncjflange.com\/\">https:\/\/www.cncjflange.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>If you\u2019ve ever worked with JIS flanges (that\u2019s Japanese Industrial Standard, for the uninitiated) and wondered &hellip; <a title=\"What are the torque requirements for tightening JIS flanges?\" class=\"hm-read-more\" href=\"http:\/\/www.primamahamaju.com\/blog\/2026\/11\/09\/what-are-the-torque-requirements-for-tightening-jis-flanges-4bf9-ac1285\/\"><span class=\"screen-reader-text\">What are the torque requirements for tightening JIS flanges?<\/span>Read more<\/a><\/p>\n","protected":false},"author":84,"featured_media":3604,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3567],"class_list":["post-3604","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-jis-ks-flanges-42a8-ac4a5a"],"_links":{"self":[{"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/posts\/3604","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/users\/84"}],"replies":[{"embeddable":true,"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/comments?post=3604"}],"version-history":[{"count":0,"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/posts\/3604\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/posts\/3604"}],"wp:attachment":[{"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/media?parent=3604"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/categories?post=3604"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.primamahamaju.com\/blog\/wp-json\/wp\/v2\/tags?post=3604"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}